Opt Zero

CMC continues LM attitude and optics tracking *CMC will react to changes made to N78 and N79 (May take 18 sec) To start VHF marks - V87E (V88E to stop) MARK at will (Reject within 10 sec) *P0SS F 06 49 ar, aV, source code* * (.Olnm, .1 fps ,0000X)* For backup marks, see V54 (p G l-26) To terminate P20 - V56E OPT ZERO - ZERO G N OPT PWR - OFF Note To display N49 for each measurement

N Alarm Codes

00110 Mark reject has been entered but Continue if alarm recurs use MDC DSKY. 00114 More marks made than desired 00115 V41 N91 keyed with OPTICS MODE not OPTICS MODE - CMC and OPTICS ZERO - OFF 00116 Optics switch altered before 15 sec zero time elapsed OPTICS ZERO - ZERO (15 sec). 00117 V41 N91 keyed but CMC has reserved OCDU (from start of gimbal test in P40 until termination of TVC functional allocation of the optics CDU Driving Output) V41 N91 not yet available 00120 Optics torque has been...

Rapid Imu Realign

(Releases Platform And Recovers PGNS Control Modes) 77E, 10000E, IE (Sets REFSMMAT FLAG) 4 V37E 51E, PRO (Sets Drift Flag) V37E 00E To Temporary Loss of DC BUS, Update CMC Clock With V55 To Complete Recovery. CHANGING LANDING SITE REFSMMAT FOR OUT-OF-PLANE BURN Load R1 0 + 90 + RLS LAT +35

Gdc Refsmmat Determination

GDC REFSMMAT REALIGN (P52) 7-15 LM Steerable Ant Pointing 7-17 8. PTC ORB RATE PROCEDURES 8-1 P20 Opt 2 (PTC Orb Rate) 8-1 Passive Thermal Control (G& N) 8-2 Passive Thermal Control (SCS) 8-3 Pitch Orb Rate Maneuver (G& N) 8-4 Pitch Orb Rate Maneuver (SCS) 8-4 9. Erasable-LOAD UPDATE 9-1 Erasable Load Update 9-1 LM or CSM S.V. Readout 9-8 10. PLANET

Erasable Load Update

In the event of PROG ALARM 1107, perform the following V74E (Wait 42 sec HBR) (DUMP E MEMORY) V36E V25N07E 77E 10000E IE (set REFSMMAT) V1N1E 104E (verify CMOON FLAG and LMOON FLAG) (BITS 11 AND 12 SHOULD BE 0 IN EARTH SPHERE and 1 in MOON SPHERE) Verify E MEMORY (should be done ASAP) V1N1E N15E, READ R1, E REPEAT FOR UPDATES A-L

Fdai Select Fdai Source Ah Set Att Set

Key VERB when nulled freeze display Record from DSKY R P Y Record ATT SET dials R_P_Y_ EMS V TEST amp NULL BIAS CHECK EMS MODE - STBY EMS FUNC - AV SET VHF RNG SET AV ind to 1586.8 fps EMS MODE - NORMAL EMS FUNC - AV TEST SPS THRUST Lt - on off 10 sec AV ind. stops at -0.1 to -41.5 EMS MODE - STBY EMS FUNC - AV SET VHF RNG SET AV ind to - 100.0 fps CMC MODE - FREE Until meas complete or BMAG MODE 3 - RATE 2 EMS FUNC - AV wait 5 sec Start DET 00 EMS MODE - NORM 40 EMS MODE - STBY If AV lt 1 fps,...

Vhf Rng Dsky Display

G amp N Recovery Procedures 1-20 V35 DSKY Condition Light Test 1-23 V41 N91 Coarse Align OCDU's 1-23 V41 N20 Coarse Align ICDU's 1-24 V42 Gyro Torquing 1-24 V48 DAP Data Load amp Activate Procedure . 1-25 V49 Crew Defined Maneuver 1-26 V54 Backup Optics Mark 1-26 V55 CMC Time Update 1-27 V57 Display FULTKFLG Condition 1-27 V64 Hi Gain Antenna Pointing 1-27 V67 W-Matrix Error Display 1-28 V74 CMC V82 Orbit Parameter Display 1-28 V83 Rndz Parameter Display 1 1-29 V85 Rndz Parameter Display 2 1-29...

Cmc General

Star Verb List Decimal 1-2 Noun List Decimal 1-4 V05 N09 Alarm Codes 1-8 V50 N25 Checklist Codes 1-14 V04 NG6 N12 Option Codes 1-14 Monitor Data in Erasable Memory 1-16 Flag Word Set Reset 1-16 Change Data in Erasable Memory 1-16 Flag Word Bit Assignments 1-17 Monitor of Input Output Channels 1-18 Channel Set Reset 1-18 CMC Input Output Channels 1-19

Gdc Align

Cb STAB CONT SYS all cb SPS 0 fCf' gt close SET AVC verify EMS FUNC - aV verify MAN ATT 3 - RATE CMD ATT DB - MIN RATE - LOW TRANS CONT PWR - ON SCS TVC 2 - RATE CMD AVCG - LM CSM or CSM TVC GMBL DRIVE P amp Y - AUTO -06 00 TVC SERVO PWR 1 - AC1 MNA TVC SERVO PWR 2 - AC2 MNB ROT CONTR PWR NORMAL 2 - AC ROT CONT PWR DIRECT 2 - OFF BMAG MODE 3 - ATT1 RATE 2 SC CONT - SCS RHC 2 - ARMED 55 00m PRIMARY TVC CHECK -05 00 GMBL MOT PI-Y1-START ON LMP Confirm Verify TRIM CONTROL amp SET Verify MTVC IF...

Q

CMC LGC Clock Sync TEPHEM Update 7-7 V55 CMC Time Update See EXT VB pg G l-27 7-7 Align LM IMU to CSM IMU 7-7 Align LM IMU to CSM GDC 7-8 Align LM AGS to CSM IMU GDC 7-8 Align CSM GDC to LM IMU 7-9 Align CSM GDC to LM AGS 7-9 Align CSM IMU to LM IMU 7-10 Align CSM IMU to LM AGS 7-11 Crescent Align 7-12